ATTENTION:

BEFORE YOU READ THE ABSTRACT OR CHAPTER ONE OF THE PROJECT TOPICS BELOW, PLEASE READ THE INFORMATION BELOW.THANK YOU!

INFORMATION:

YOU CAN GET THE COMPLETE PROJECT OF THE TOPIC BELOW. THE FULL PROJECT COST N5,000 ONLY. THE FULL INFORMATION ON HOW TO PAY AND GET THE COMPLETE PROJECT IS AT THE BOTTOM OF THIS PAGE. OR

YOU CAN CALL: 08068231953, 08137701720

WHATSAPP US ON: 08137701720

STATISTICAL MODELLING AND OPTIMIZATION OF THE DRYING CHARACTERISTICS OF MUSA PARADISIACA (UNRIPE PLANTAIN)

CHAPTER ONE

INTRODUCTION

1.1. BACKGROUND OF THE STUDY

Drying is probably the oldest and the most important method of food preservation practiced by humans. This process improves the food stability, since it reduces considerably the water and microbiological activity of the material and minimizes physical and chemical changes during its storage.

Musa paradisiacal (unripe plantain) is an important staple food in Central and West Africa, which along with bananas provides 60 million people with 25% of their calories. According to FAO, (2004), over 2.11 million metric tons of plantain is produced in Nigeria annually. Plantain for local consumption, plays a role in food and income security and has the potential to contribute to national food security and reduce rural poverty.

Unripe plantain has rich iron nutrient content (Aremu, et al., 1990). However, they are highly perishable and subject to fast deteriorations, as their moisture contents and high metabolic activity persist after harvest (Demirel, et al., 2003).

Moreso, about 35-60% post-harvest losses had been reported and attributed to lack of storage facilities and inappropriate technologies for food processing. Air drying alone or together with sun drying is largely used for preserving unripe plantain. Besides helping preservation, drying adds value to plantain.

1.2 STATEMENT OF THE PROBLEM

Drying consists of a critical step by reducing the water activity of the products being dried. Hot air drying of agricultural products is one of the most popular preservation methods because of its simplicity and low cost. Thin layer drying is a common method and widely used for fruits and vegetables to prolong their shelf life.

However, drying of any food substance is an energy intensive operation with grave industrial consequences, and must be performed with optimal energy utilization. This project work seeks to ascertain the best thin layer model and the temperature and slice thickness that optimizes time.

1.3 OBJECTIVES OF THE STUDY

The objectives of this work are to;

Ascertain the type of thin-layer model that best fits the moisture ratio/time data during the drying of unripe plantain.

To determine the temperature and slice thickness that optimizes time (i.e. gives the shortest drying time).

1.4 JUSTIFICATION OF THE STUDY

Production of plantain is seasonal while consumption is all year round and therefore there is the need to cut down on post-harvest losses by processing them into forms with reduced moisture content.

This agricultural product has high moisture content at harvest and therefore cannot be preserved for more than some few days under ambient conditions of 20oC – 25oC (Chua, et al., 2001). This post-harvest loss results in seasonal unavailability and limitations on the use by urban populations. Plantain has however been having an increasing surplus production since 2001 (Dankye, et al., 2007). It is estimated that in 2015, there will be a surplus of about 852,000 Mt. This means that these surpluses have to be exported, processed or go to waste.

A reduction in moisture content potentially increases shelf life and hence prevents excessive post-harvest loss and that drying is an alternative to developing nations, where there is deterioration due to poor storage, weather conditions and processing facilities

1.5 SCOPE OF THE STUDY

The scope of this project work includes the following:

Using the ten selected thin layer models to investigate the one that best fits the data generated from drying of unripe plantain at specified temperatures, slice thicknesses, and drying time.

Using regression analysis to obtain the slice thickness and temperature for the optimum (minimum) drying time.

HOW TO RECEIVE PROJECT MATERICAL(S)

After paying the appropriate amount (#5,000) into our bank Account below, send the following information to

08068231953 or 08168759420

(1)    Your project topics

(2)     Email Address

(3)     Payment Name

(4)    Teller Number

We will send your material(s) after we receive bank alert

BANK ACCOUNTS

Account Name: AMUTAH DANIEL CHUKWUDI

Account Number: 0046579864

Bank: GTBank.

OR

Account Name: AMUTAH DANIEL CHUKWUDI

Account Number: 3139283609

Bank: FIRST BANK

FOR MORE INFORMATION, CALL:

08068231953 or 08168759420

AFFILIATE LINKS:

easyprojectmaterials.com

googleprojectsng.blogspot.com

myprojectsng.blogspot.com.ng

https://projectmaterialsng.blogspot.com.ng/
https://foreasyprojectmaterials.blogspot.com.ng/
https://mypostumes.blogspot.com.ng/
https://myeasymaterials.blogspot.com.ng/
https://eazyprojectsmaterial.blogspot.com.ng/
https://easzprojectmaterial.blogspot.com.ng/

easyprojectmaterials.com.ng

http://graduateprojects.com.ng/

http://freshprojects.com.ng/

http://info247.com.ng/

projectgtaduates.com.ng

projectmarket.com.ng

projectschool.com.ng

projectstudent.com.ng

projectshop.com.ng

projectstores.com.ng

projectarena.com.ng

projectbases.com.ng

projectwisdom.com.ng

projectsense.com.ng

projecttorch.com.ng

projectlamp.com.ng

projectmentor.com.ng

projectteacher.com.ng

projectjunction.com.ng

projectstop.com.ng

By admin

Leave a Reply

Your email address will not be published. Required fields are marked *